Please choose a Location for Pickup or Post
All Department
Computer Hardware

Thermaltake Water 3.0 Riing RGB 240mm AIO Liquid CPU Cooler

Price: $185.0

Stock:Loading...

RRP:$195.0
Buy Now, Pay Later with  zipPay More info »
    • Milton1

    • Epping1

  • Qty:
    Minus Increase
  • Products Name: Thermaltake Water 3.0 Riing RGB 240mm AIO Liquid CPU Cooler
  • Model#: CL-W107-PL12SW-A
  • Brand: Thermaltake
  • Last Update:
  • Net Weight: 3.000Kg
  • Warranty: 12 Months
  • Category : CPU Cooling
  • Fans Size etc. : 120mm
  • CPU Cooling Category : Water Cooling (all in one)


Thermaltake Water 3.0 Riing RGB 240
Designed to meet the demands of enthusiasts, Thermaltake releases the latest Water 3.0 Riing RGB Series, a RGB 256 colors all-in-one liquid cooler with dual 120mm powerful high static pressure fans and a smart fan controller. Choose from: 240mm and 360mm highly-efficient radiators to control any escalating CPU temperatures. The new All-In-One LCS Water 3.0 Riing RGB is designed to exceed user expectations.



Compatibility Intel LGA 2011-3/2011/1366/1156/1155/1151/1150
AMD FM2/FM1/AM3+/AM3/AM2+/AM2
Water Block Material:Copper
Pump Rated Voltage:12 V
Rated Current:175 mA
Fan Dimension: 120 x 120 x 25 mm
Speed:800 ~ 1500 R.P.M
400 ~ 1000 R.P.M (Low Noise Mode)
Noise Level:18.5 ~ 26.4 dB-A
Rated Voltage:12 V
Max. Air Flow:22.14 ~ 40.6 CFM
Max. Pressure:0.57 ~ 2.01 mm-H2O
Connector:4 pin
Radiator Dimension:270 x 120 x 27 mm
Tube

Length:326 mm
Material:Rubber

Weight 1071g
Caution

Thermaltake recommends the following steps to be taken before using the Pacific series radiators and water blocks
To ensure a clean loop, flush and rinse your radiators and water blocks with distilled water prior to use.
Do not use tap water or distilled water as your coolant, it may harm your loop and reduce performance.
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while protecting the entire liquid loop from corrosion.
Before storing your water cooling components, please clean, rinse and dry. This will ensure a longer lifespan for your components.

Thermaltake recommends the following steps to be taken after completing your water loop setup
It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance while preventing the entire cooling system copper, brass, nickel, aluminum, and steel from corrosion.
Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
Fill the reservoir to the top as it will prevent air from going into the pump
If necessary tilt the system slightly from side to side to bleed the air out of the loop.
Place some paper towels under fittings and joining points to test for leaks.
Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop
Before starting, flush out your system correctly to prevent any coolant or unwanted particles sticking to your tubes, radiators and other cooling components.
Coolant might fade over time.


* Specifications are subject to change without notice.
* Specifications may vary.
* The product picture(s) is only for your reference, it may differ from the actual product.



Thermaltake Water 3.0 Riing RGB 240mm AIO Liquid CPU Cooler

Thermaltake Water 3.0 Riing RGB 240mm AIO Liquid CPU Cooler